Mobility scooter and wheelchair hoists
Using a hoist to lift a wheelchair or mobility scooter into a car:
Hoists for lighter chairs are usually two-way hoists. They lift the chair up and down by power but you push the chair by hand to swing it into the car.
- use power to swing the wheelchair into the car AND lift it up and down
- are generally used if your scooter or wheelchair is heavy
- are easier to use on roads with steep slopes or hills since you don't have to push your wheelchair up into the boot
- can be fitted to almost any vehicle, while others are made for larger vehicles such as estates, 4x4s or MPVs
Six-way hoists: Autoadapt have a number of six-way powered hoists (distributed by Elap Mobility) where the swinging arm is telescopic and moves in and out under power. This allows for more flexibility in where the wheelchair/scooter is picked up/set down.
Telescopic hoist: Brig-Ayd Controls have a telescopic hoist that picks up the wheelchair/scooter and loads it into the boot in one continuous action.
Using a hoist to get a wheelchair or mobility scooter into a car
You'll probably need:
- to use both hands to use the hoist
- to be able to stand without much support while you are hooking on and lifting the wheelchair or scooter
- to fold or dismantle the wheelchair or scooter before you lift it, especially if you have a small car or a large or heavy wheelchair or scooter
Attaching the hoist
There are different ways of attaching the hoist to the wheelchair - open hooks or hooks that close:
- open hooks are easier to use but can come off when the lifting cord is slack
- closed hooks may be more awkward If you have limited grip or dexterity,
- if the hook has a spring, try it to see whether you need both hands, or if your fingers get caught easily
You need to use both hands for some hoists - one to hold it in the right place to stop the hooks falling loose, and the other to take up the tension with the control unit. This may be difficult to do standing if you have poor balance.
Nearly all suppliers provide a range of hooks, so discuss what you need with them before you buy, and make sure you try all the functions.
WIth four-way hoists especially, the wheelchair/scooter needs to be in just the right place, which may take a bit of getting used to.
Controlling the hoist
Most hoists have hand-held control units which can be:
- either attached by wires
On a few hoists, there are control units that are fixed to the hoist's arm or base which means you can hold on for support while you're using it. Some people find these easier to use than a hand-held control.
Most suppliers have a choice of switches and should be able to find something to suit you. Try the control before you buy.
On some hoists, you have to remove the lifting arm when the wheelchair is stowed in the boot.
If you're travelling without your wheelchair, some hoists allow you to remove the swinging arm to get it out of the way, leaving more room for luggage. The removable parts can be heavy, especially on heavier-duty hoists. Some can't be taken out of the car because the lifting cords are permanently threaded through them.
What hoists are available?
There is a wide variety of hoists available. You can see summaries of the available products, listed in order of the maximum weight they can lift in our product guide:
Platform lifts for mobility scooters and wheelchairs
As an alternative to hoists, use a platform lift to load an unoccupied wheelchair or mobility scooter into the boot.
To use a platform lift:
- you bring the platform out of the boot under power
- push or drive the wheelchair on and secure it
- and then transfer the platform back into the boot
Platform lifts are easier than a hoist because:
- you don't need to fold or dismantle the wheelchair or scooter
- you don't need the same strength or dexterity to load the wheelchair
- you can secure the wheelchair to the platform before loading
Platform lifts are:
- generally used for larger wheelchairs and scooters and they need quite a large load space (see our car search)
- designed to fit in MPVs, large estates and vans.
- best fitted into a boot at least 120cm wide and at least 70cm deep (sometimes back seats need to be removed)
- a bulky solution: you need the same amount of room behind the vehicle to load the wheelchair onto the lift platform
Overview of the lifts available
Price including fitting: £1,998
Max weight lifted (kg): 115
Platform size (cm): 69 x 120 / 77.5 x 155 ('twin')
Space required (h x w x d; cm): 102 x 122 x 122 / 102 x 123 x 122 ('twin')
Distributed by: Alfred Bekker
Price including fitting: about £2,200
Max weight lifted (kg): 159
Platform size (cm): 69 x 112
Space required (h x w x d; cm): 102 x 112 x 115
Distributed by: Elap Mobility
Last updated: February 2015